Mobilect 39

Electrical insulating oils

  • 安全数据表 (MSDS)
  • 产品数据表 (PDS)

Mobilect™ 39 is a high quality mineral uninhibited insulating oil with very good dielectric properties and oxidation stability intended for transformers, switchgears and other electrical equipment.

Mobilect 39 is uninhibited and meets the specifications IEC 60296 (04) and ASTM D1275B / CIGRE corrosion tests requirements.

设备润滑油推荐

我们的美孚优释达℠产品选择器工具将帮您发现适用于具体设备的润滑油。

查找您的设备

{{list.title}}

< Back

没有看到您的设备制造商 联系我们的帮助台按应用搜索 >

联系我们的帮助台 分享给朋友 查找经销商

数据表

产品数据表 (PDS)
安全数据表 (MSDS)

技术资源

变压器油油品分析和测试

了解美孚 Mobilect™ 39 变压器油油品分析和测试的重要参数。

专家讲堂, 文章

所有 项资源

 

Features and Benefits

  • Mobilect 39 has a high resistance to thermal and chemical degradation in the presence of iron and copper, which reduces tendencies to produce sludge and oil-soluble oxidation products. When lower quality oils are used these may form deposits in the transformer and impede heat transfer by interfering with convection currents. In addition deposits may accelerate insulation defects and are often very difficult to remove without complete dismantling.
  • Mobilect 39 is specifically treated during manufacture to remove moisture. Water will reduce the electrical insulating properties of the oil and promote oxidation. It is important to remember that a dry oil is hygroscopic and absorbs moisture from the air. It must therefore always be stored in dry conditions and well-closed containers. It is strongly recommended to dry the product before use or use it within short notice after purchasing to avoid long term storage.
  • The dielectric strength of Mobilect 39 is a measure of the resistance of the oil to electric stress and is expressed in kV across a specified gap under test conditions. This is not a measure of the quality of the oil but of the absence of contaminants - especially moisture, fibres and polar chemicals.
  • Mobilect 39 is free from wax even at low temperatures and thus circulates freely in outdoor applications. Its viscosity ensures readily heat transfer by mobile convection currents. Mobility is also essential to quick quenching of arcs in switchgear units.
  • The low pour point of Mobilect 39 ensures a free flow in most conditions between the transformer and the conservator and maintains the reliability of tap changers at the lowest temperatures. 

 

Applications

  • Mobilect 39 is recommended for use in oil filled transformers and switchgears in which the oil is required as an insulation medium or as a heat transfer medium.
  • Mobilect 39 is to be used in applications specifying IEC 60296 (04) General Specifications and reinforced copper corrosion protection (pass ASTM D1275B corrosion test).
  • Mobilect 39 is not suitable for use in oil filled cables, for special impregnation processes or for use in capacitors.

 

Specifications and Approvals

Mobilect 39 meets or exceeds the requirements of: 
IEC 60296 (04) General Specifications 

 

Typical Properties

Mobilect 39 
Density at 20°C, kg/dm³, ISO 121850.883
Viscosity, mm2.s-1 @ 40°C, ISO 31049.5
Flash Point (PMCC), °C, ISO 2719148
Pour Point, °C, ISO 3016- 54
Corrosive Sulphur, ASTM D1275 procedure BNon Corrosive
Oxidation Stability @ 120°C /164 h, IEC 61 125C 
- Total Acidity, mg KOH/g0.31
- sludge, wt%0.11
Dielectric Dissipation Factor @ 90°C, IEC 60247‹ 0.001
Interfacial Tension, mN/m, ISO 6295› 40
Breakdown voltage, 
- before treatment, kV, IEC 60156› 30
- after treatment, kV, IEC 60156› 70

 

Health and Safety

Based on available information, this product is not expected to produce adverse effects on health when used for the intended application and the recommendations provided in the Material Safety Data Sheet (MSDS) are followed. MSDS's are available upon request through your sales contact office, or via the Internet or will be provided by seller to customers if and as legally required. This product should not be used for purposes other than its intended use. If disposing of used product, take care to protect the environment.

加载中